Murkwood swamp mini map

[Legacy_Builder_Anthony]

               I tried adjust my hak oredr a few differnt ways but it seems the raise and lower cause the mini map to turn white.I have the murkwood pacth below the murkwood hak.Im not sure if anyone else has this problem.Maaybe worm will stop in here and comment.I dont know maybe somethings messen it up from my other haks but whats your thoughts?
               
               

               
            

[Legacy_Builder_Anthony]

               I still am seeing white on raised areas in the minimap.Does anyone here use murkwood swamps?
               
               

               

                     Modifié par Builder_Anthony, 12 mai 2011 - 03:44 .
                     
                  

            

[Legacy_lordofworms]

               which version are you using? might I ask first? i.e. whats the name of the hak itself.?
               
               

               
            

[Legacy_Builder_Anthony]

               19.6 MB
P1 Pacth

I looked at your new haks out....
Do i need all four of those haks for murkwood now?
Should i scrap the 19.6 and p1 if i use the new ones?
               
               

               

                     Modifié par Builder_Anthony, 12 mai 2011 - 06:25 .
                     
                  

            

[Legacy_lordofworms]

               this is the newest version here..v16
try this one...without any patches,etc

http://nwvault.ign.c....Detail&id=6631

download all 4 to the same location then when all 4 are downloaded extract the .hak file and use that one.
               
               

               
            

[Legacy_Builder_Anthony]

               Ok i put all four in the hak folder and took my old ones out but when i go to add the hak to the mod there is no hak in the drop down list that says murkwood.So basicly im not seeing it on the custom content list in the toolset.Did you rename it?
               
               

               
            

[Legacy_Bannor Bloodfist]

               

Builder_Anthony wrote...

Ok i put all four in the hak folder and took my old ones out but when i go to add the hak to the mod there is no hak in the drop down list that says murkwood.So basicly im not seeing it on the custom content list in the toolset.Did you rename it?

Those 4 files do NOT belong in your hak folder.

Use 7zip or winrar and extract the hak from inside of them, they are 4 pieces of a single archive file, that was split into smaller parts to make it easier for him to put it on the vault (less than 25 meg you can directly upload, larger, has to go through the FTP process and requires human intervention by vault admin).

Anyway, open the first file the .001 version, and it will allow you to extract all of it.  Inside that archive is a single hak named without quiotes "~mirkv16.hak".  If you notice the first character is the tilde "~" which really should NOT be used for a file name, but it works and some folks insist on using things like that because they think they are special people, anyway places that hak at the TOP of an alphabetically sorted list, which is what the toolset displays for you.
               
               

               
            

[Legacy_Builder_Anthony]

               Ok i have winrar so i will open up all of the files and extract them to the desktop....i dont put them into the hak file except for one of them?
               
               

               
            

[Legacy_Bannor Bloodfist]

               It is only ONE file inside 4 pieces, you open the .001 file and extract it, it will automatically extract the rest of the pieces from the other three files.  Leaving you with ONE hak file that is extracted.  That ONE hak file goes into your hak folder.

To be honest, I am not positive that winrar will handle this one, you likely will need to download the 7zip program.
               
               

               

                     Modifié par Bannor Bloodfist, 15 mai 2011 - 04:12 .
                     
                  

            

[Legacy_Builder_Anthony]

               I redownloaded everything and i get these files that "are not in any folder."

The names on them are how they appear on my desktop right after downloading them.I use winrar and uasually they are in a folder and then i can extract them.Im not able to do that because they appear unrar or unzipped already.This is how they apperar on my desktop.
mirkv16.7z.001
mirkv16.7z.002
mirkv16.7z.003
mirkv16.7z.004
Since i cant open         mirkv16.7z001  and have it run to create the hak.I am clueless what to do.
               
               

               

                     Modifié par Builder_Anthony, 16 mai 2011 - 12:55 .
                     
                  

            

[Legacy_Calvinthesneak]

               Download 7zip and try.  I suspect winrar isn't capable of handling multi part 7z files.
               
               

               
            

[Legacy_Builder_Anthony]

               Thankyou
I did need 7zip

I have 2 questions though would players have to do the same thing or just download those 4 files.

Could i just make it into one giant hak pack that auto installs it with other haks?
               
               

               

                     Modifié par Builder_Anthony, 16 mai 2011 - 01:24 .
                     
                  

            

[Legacy_Bannor Bloodfist]

               Players would have to do the same download/extract option.  

Technically, you could put a copy into another hak, but you should ask for permission to do that from Worm first.  If you DID put the content into another hak, you would have to make that hak available to your prospective players.
               
               

               
            

[Legacy_Builder_Anthony]

               I realy like the updates he did but i know nwn players wont go threw the steps needed to get he new mirkwood.Thats why im concerened on the ease of downloading.I been thinking of makeing a hak auto installer where they click one button and it adds all the haks into the hak file by itself.Is that possible with that being split up like that?I also hear what your saying about that it needs to downloaded from somewhere.Isnt there a place other then the vault that could support the large file as just ~mirkwood.
               
               

               
            

[Legacy_Builder_Anthony]

               bump